DESIGN AND CONSTRUCTION OF DUAL POWER SUPPLY

CHAPTER ONE

1.1       INTRODUCTION

            Nowadays accurate personal identification is becoming more and more important. Usual means (smart cards, passwords…) have shown their limits (falsification, loss…). Biometrics (i.e. analysis of personal biological characteristics) can bring a satisfying answer to those latter problems. Currently fingerprint recognition is the most widely used technique for personal identification. Fingerprints are made up of locally parallel ridges with singular points (minutiae), and they constitute a unique permanent universal pattern. The use of ink and paper to get an image from a finger was used for a long time, but technological advances have enabled to automate the acquisition stage by means of solid-state sensors. These sensors exploit different techniques to acquire the image (pressure, electrical field, temperature…) and require a static (matrix sensor) or mobile finger position (sweeping mode sensor).

Our project is developed to provide security for a Organization. In this project the fingerprint sensor sense the thumb impression of the corresponding person and that image will be compared with registered image, if the both images are unique, then the finger print device activates particular task like access control to a secured area, identification of the employee etc.  The project contains 2 modes, the first one is master mode and the second is user mode. The master mode is used to register the new user and gives the mode of authorization. The master mode has the ability to create and delete the users. The user mode is an ordinary mode used for the authentication of the employees. In user mode of authorization, creation and deletion of a user cannot be performed.

The Master mode operations are done directly through interfacing the FM10 (Finger Print Module) to the COM PORT of the computer. The application program is developed using java API in Swings. The Java communication API is used for communicating with the Fingerprint device. The employee details along with biometric information database are stored in the flash memory of the Fingerprint module. The Microcontroller 89S52 is programmed to operate under user mode. Microcontroller is programmed using C51 cross compiler. Fingerprint image is scanned by the fingerprint device. If the scanned image matches with the registered image then Microcontroller sends the authorized persons Id to the computer when the person enters and leaves the organization. By this daily attendance of employees, many employee records are maintained. The employee records are stored in

1.2       OBJECTIVES OF STUDY

The aim and objectives of this project work is to design and constructs a dual power supply for use in industries, homes, etc or any property.

1.3       PROBLEM STATEMENT

This project provide a comprehensive of a finger print security alert system with LCD display with a central alert unit and the technique employed in the design,

Construction and analysis of the various circuit components. The technology employed in constructions of a security system such as this shows how each component relatively function with each other and the combined operations of sub-circuits placed at each exit response to any intrusion.

1.4       SIGNIFICANCE OF STUDY          

The study is important in numerous aspect as it may find its application in almost all electronics appliances. It can be applied in homes, hospitals, factories or industries etc to give positive and negative feedback.          

1.5       SCOPE OF STUDY

Short comings may be experience due to inherent weakness in designs considering the time frame which the project was carried out.

CHAPTER TWO

LITERATURE REVIEW

2.0       INTRODUCTION

A power supply is an electronic device that supplies electric energy to an electrical load. The primary function of a power supply is to convert one form of electrical energy to another and, as a result, power supplies are sometimes referred to as electric power converters. Some power supplies are discrete, stand-alone devices, whereas others are built into larger devices along with their loads. Examples of the latter include power supplies found in desktop computers and consumer electronics devices.

Every power supply must obtain the energy it supplies to its load, as well as any energy it consumes while performing that task, from an energy source. Depending on its design, a power supply may obtain energy from various types of energy sources, including electrical energy transmission systems, energy storage devices such as a batteries and fuel cells, electromechanical systems such as generators and alternators, solar power converters, or another power supply.

---

REQUEST FOR PROJECT MATERIAL

Good Day Sir/Ma,

WARNINGS!

PLEASE make sure your project topic or related topic is found on this website and that you have preview the abstract or chapter one before making payment.

Thanks for your interest in the research topic. The complete research work will cost you N2000 and we will send the material to you within 24hours after confirming your payment.

Make the payment of N2000 into any of the account number below and we will send the complete material to you within 24hours after confirming your payment.

Account Name: Agada Leonard E
Account No: 2070537235
Bank: UBA

Or

Account Name: Agada Leonard E
Account No: 3049262877
Bank: First Bank

Or

Account Name: Agada Leonard
Account No: 0081241151
Bank: Diamond Bank

After payment, send the following information to us through this email
address: enemsly@gmail.com

Topic paid for:
Amount Paid:
Date of Payment:
Teller No or Transaction ID:
Name of Depositor:
Depositor Phone Number:
Email address:

NOTE: The material will be forwarded to the email address you provided
within 24hrs after confirmation of the payment.

Thanks.

Agada Leonard E.
For: Enems Project.

 For more information visit our contact page @ CONTACT US

---